humanoid robotic tools arduino mega2560, due, nano, shield,drive

$5.00

Description

Location : Delta, BC V4M 3M2

i have finished my part 1 prototyping
for my humanoid robot, so these are
ALL NEW, in original packaging,
NEVER USED, unless otherwise stated;
prices varies by parts;

next part will be parts for the humanoid robot
frame…so watch out;

thanks to you all for your purchases, following
is what are left:

short list:

arduino(none came with cables)
all original R3, unopen, never used:
due 1 unit left with heatsink 25$cd/unit FIRM
mega2560 2 units left 25$cd/unit FIRM
nano 1 unit left 5$/unit FIRM
nano expansion shields 2 unit price: 5$cd/unit FIRM

monster vnh2sp30 4 units price: 25$cd/unit FIRM

battery holder 6 cells 1.5v AA with jack
my price: 5$/unit FIRM

kingston micro sd cards, new+unopen 8gb 32gb both with jacket
10$ for both

Detail list of above with specs+reason for selling + prices:

THE ARDUINO DUE R3:
SPECS:
Microcontroller     AT91SAM3X8E
Operating Voltage     3.3V
Input Voltage (recommended)     7-12V
Input Voltage (limits)     6-16V
Digital I/O Pins     54 (of which 12 provide PWM output)
Analog Input Pins     12
Analog Output Pins     2 (DAC)
Total DC Output Current on all I/O lines     130 mA
DC Current for 3.3V Pin     800 mA
DC Current for 5V Pin     800 mA
Flash Memory     512 KB all available for the user applications
SRAM     96 KB (two banks: 64KB and 32KB)
Clock Speed     84 MHz
Length     101.52 mm
Width     53.3 mm
Weight     36 g

comes with heat sink installed,
price: 25$cd/unit FIRM

on the market, other popular sites listed prices:
robotshop: 51.33$us/unit+shipping
digipart: 59.06$us/unit+shipping
3Dprinting: 25.95$us/unit+shipping
amazon: 52.99$cd+shipping
sparkfun: 41.95$us+shipping

comment on+reason why i am selling:
this is arduino FIRST ARM board,
it is very powerful, the problem is
NOT ARDUINO, but device suppliers
that provide devices+firmware to
be used is limited and the supported
software need constant updates;
but if you are using those devices
supported on mega2560, i know i did
not have problems, so you should also
not have problems;
and if you use a USB HOST SHIELD 2.0(
and i have ), you can access usb hard drive
upto 2TB

remember this is a board that will take
MAX 3.3v FOR INPUT, and MAX 5V FOR OUTPUT…
so any devices REQUIRES over 5v…you will NEED
A DRIVER, and NOT those arduino sensor shields
because they are all based on 5V…

ALSO this DUE R3 will NOT WORK WITH THESE
ULTRASONIC SENSORS: HC-SR04 OR US-015
AND IT WILL WORK WITH SRF-02(AN ULTRA-SONIC SENSOR
WITH POOR RANGE CAPABILITIES) and us-100

specs:
54 digital input/output pins (of which 15 can be used as PWM outputs),
16 analog inputs,
4 UARTs (hardware serial ports),
16 MHz crystal oscillator

Microcontroller     ATmega2560
Operating Voltage     5V
Input Voltage (recommended)     7-12V
Input Voltage (limit)     6-20V
Digital I/O Pins     54 (of which 15 provide PWM output)
Analog Input Pins     16
DC Current per I/O Pin     20 mA
DC Current for 3.3V Pin     50 mA
Flash Memory     256 KB of which 8 KB used by bootloader
SRAM     8 KB
EEPROM     4 KB
Clock Speed     16 MHz
LED_BUILTIN     13
Length     101.52 mm
Width     53.3 mm
Weight     37 g

from these popular marketed prices
they ALL have this in common: NO CABLE
progressiveautomations.ca/products/ 56.63$c
newark.com 47.26$+shipping
amazon.ca 50.99$cd free shipping
sparkfun.com 38.95+shipping

CLONE(no clone/compatible by me):
Elegoo MEGA 2560 R3 Board ATmega2560 21$
WITH CABLE

reason for selling: these are my remaining extras from my project
my price: 25$unit price is firm

motor/servo drivers:

arduino vnh2sp30 servo driver 25$
comes with heat sink installed,

i have 8 units, and using 4 to
drive 8 super500 servos each
servo needs CONSISTENT 14amps
and 16VOLTS and this vnh2sp30
monster driver do this

as to battery… you will need battery
that WILL PROVIDE CONSISTENT
MINIMUM 14AMPS+16VOLTS…

vnh2sp30
you will require to use this kind of drive
if your servo/dc motor/stepper requires 12V
and more, otherwise you will not need this driver
SPECS:
Voltage Max: 16V.
Maximum current rating: 30 A.
Practical Continuous Current: 14 A.
Current sensing available to Arduino analog pin.
MOSFET on-resistance: 19 mOhms (per leg)
Maximum PWM frequency: 20 kHz.
Thermal Shutdown.
i have 4 units left
servo that needs CONSISTENT
14amps and 16VOLTS and this
vnh2sp30 monster driver do this

as to battery… you will need battery
that WILL PROVIDE CONSISTENT
MINIMUM 14AMPS+16VOLTS…

for reference+program code on how to use this vnh2sp30:
https://www.instructables.com/id/Monster-Motor-Shield-VNH2SP30/
and you will need to download and use arduino ide to do the programming

on the market, other popular sites listed prices:
robotshop: 71.95$us/unit+shipping
digipart: 56.58$us/unit+shipping
walmart: 69.95$US/unit
ebay+amazon: availability UNKNOWN
price: 25$cd/unit FIRM

comment on:
a) vnh2sp30 aka monster driver, it is very powerful
and if you do not have any servo/stepper that needs
CONSISTENT 14v AND 14A, you will not need this driver

b) vnh3sp30 … it is MUCH MORE COMPACT+
FUNCTIONAL, as i have, you will have
a problem to connect to an arduino/
raspberry pi because of the pins

battery holder 6 cells 1.5v AA with jack
9 units available, my price: 5$/unit FIRM

reason for this sale: i found a jack
to hook 6 pcbs into 2 of these battery holders

prices by popular sites
amazon.ca 21.99 for 2 units+shipping+tax
there cheaper ones, like 3.77$cd…without the jack

kingston micro sd cards, new+unopen 8gb 32gb both with jacket
10$ for both

contact by email

thanks for reading/interest and have a good day+stay healthy!!!

 

 

Write a Review
Safety tips for deal
  1. Use a safe location to meet seller
  2. Avoid cash transactions
  3. Beware of unrealistic offers

Featured Ads

Top